Jlg 1350sjp operating manual pdf download

Page Select Indicator Panel 4. Jib Stow Override Steer Select Boom Control Select 5. Jib Swing Figure Page 43 Creep Mode.

Platform Rotate This switch allows the operator to rotate the basket to the left or right. Page 44 Move right to swing right, move left to by leaving the engine at mid speed and the drive motors swing left. Page 45 In this mode the front and rear axles steer in descending a grade. Horn circle for maneuvering in confined areas. If pressed, this switch supplies power to the horn. Page 46 Automatic, lift and telescope movements are matic position. The out of the operating envelope for the selected capacity.

All func- tions will default to creep if the boom is extended past — JLG Lift — Fuel Level Axles Set 4. Platform Capacity 9. Creep Speed Boom Control System Warning 5.

Tilt Alarm Warning System Distress Figure Page Present 8. Page 50 Indicates the glow plugs are operating. Page Fuel Level Indicator Refer to the Service Manual for instructions concerning the trouble codes and trouble code retrieval. Page 52 If a failure is discovered, the system further in either direction, the Drive Orientation indicator must be repaired by JLG authorized service personnel will illuminate when the drive function is selected. This is before the machine can be used.

Page Section 4. Machine Operation Swing, and are to be used in an emergency to lower the plat- form to the ground should the operator in the platform be 4. All machine systems are functioning properly. Proper tire pressure. Machine is as originally equipped from JLG. Page Controlled Arc i. This means that when — JLG Lift — Page Envelope Tracking The boom control system sensors sense the distance the cally by the boom control system to reduce machine platform is extended from the turntable, allowing higher motions.

NOTE: Operation in the lb. After engine has had sufficient time to warm up, shut engine off. The JLG Control System auto- matically shuts the engine down before the fuel tank is emptied unless the machine is set up for Engine Restart. If the indicator is illuminated, operate the Drive function in the following manner: — JLG Lift — Page Platform Down and hold until the desired platform position is obtained.

Page 4. Retract, lower and position boom in travel position; lock turntable. Drive Disconnect Hub 3. Reconnect the drive hubs by inverting the disconnect cap when towing is complete.

Drive machine to a reasonably well protected area. Call JLG Industries or weigh the individual unit to find 2. Ensure boom is lowered over rear drive axle. Push in the Emergency Stop at Platform Controls. Page Tie Down 3. Push and hold the Jib Stow control switch until the jib 3.

Secure the chassis and the platform using straps or and platform are in the stowed position under the boom. Page 76 — JLG Lift — Page 77 Spanish English — JLG Lift — Page 80 — JLG Lift — Page 81 Spanish English — JLG Lift — Page Section 5. JLG Industries, Inc. Once clear, restart the engine and return the platform to the ground. Inspect the machine for damage before continued use of the machine. Page Section 6. Page Dimensional Data Page Chassis 25, lbs.

Page Tires Cooling System 5 Quarts 4. Page Hydraulic Oil F. Aside from JLG recommendations, it is not advisable to mix oils of different brands or types, as they may not contain the same required additives or be of comparable viscosities. If use of hydraulic oil other than Mobilfluid is desired, contact JLG Industries for proper recommendations.

Page Mobil Eal H 46 Specs 7. Page 95 HYD. Page 97 HYD. Fill to cover ring gear. Pour lubricant into fill hours of operation port until it just starts to flow out of check port. Pour lubricant into fill port until it just starts to flow out of check port. Change every 2 years or hours of operation. Page 11 Quarts Adjust final oil level by mark on dipstick.

Platform Filter Tire Inflation The air pressure for pneumatic tires must be equal to the air pressure that is stenciled on the side of the JLG product or rim decal for safe and proper operational characteristics. Page Tire Replacement Please refer to the factory recommendations, may result in an unsafe condition JLG Parts Manual for the part number of the approved tires for a regarding stability. If not using a JLG approved replace Page Wheel Torque Chart ft.

Wheel nuts should be torqued before first road use and after each wheel removal. View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file. Get 1 for every download of your manual. Buy as much as you need. Connector - Purchase Separately SN to. Pin, Sensor Prior to SN Pin, Sensor SN to Present. Arm, Steer Prior to SN Arm, Steer SN to Present. Note: Original Equipment hub may have been replaced with. Service Replacement.

Refer to tag on hub for identification. Refer to tag on hub for identification before. SN through. When replacing complete hub, note that all 4 hubs. Refer to Operation and Safety or Service and Maintenance. Note: Unless there is capability to torque shaft item 4 to